Marvel ML15CLP2LP Guía del propietario Pagina 16
- Pagina / 96
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
16
CLEANING YOUR ICE MACHINE
Once you have your cleaner:
Turn the ice machine off by pressing and holding the
"ON/OFF" icon for 3 seconds. "OFF" will be dis-
played on the control.
Follow the following three step procedure for
removing the grid cutter cover from the ice machine, Refer
to Figures 23 and 24:
Remove all ice from the ice bin, (see Figure 24).
Drain the water from the water reservoir, by removing the
black plug from the bottom of the fresh water reservoir.
(See Figure 25). After the water is drained replace the plug
in the bottom of the reservoir.
Allow all of the ice to fall from the evaporator plate and
remove any ice from the grid cutter. If there is ice embed-
ded in the grid cutter wires, wait for it to melt and fall out.
Do not try to remove ice that is embedded in the grid
cutter wires as that may break the wires. (See Figures
21 and 22).
OFF
Forcing ice through the grid cutter will break the grid cutter
wires.
!
CAUTION
!
CAUTION
Remove all ice
from the evapora-
tor plate and grid
cutter area that is
not embedded in
wires
Figure 21
Figure 22
ICE
Options menu:
Normal and ECO mode:
Your ice machine comes with an optional "ECO" mode.
While in this mode ice production will slow and the appli-
ance will use less water and electricity. "ECO" mode should
only be initiated after there is a full bin of ice. To
enter "ECO" mode do the following:
• Press the "MENU" icon twice and the green
"ECO" will ash.
• Press and hold the "ON/OFF" icon until the
green "ECO" stops ashing and remains illumi-
nated.
• To return to the standard operating rate press
the "MENU" icon twice, the ECO will turn off and
the "ICE" will be ashing. Press and hold the
"ON/OFF" icon until the "ICE" stops ashing
and remains illuminated.
ECO
1
2
3
-pull out on this corner rst to remove the cover corner
from the mounting peg.
-pull out on this corner next to remove it from the
mounting peg.
-reach behind cover and push cover towards you to
remove cover from the center mounting peg.
Clean mode:
To ensure maximum performance and ice quality, it is
recommended to clean your ice machine once every six
months.
NOTE
For reference see our "Care and Cleaning video" at the
website: www.marvelrefrigeration.com.
Use only approved ice machine cleaners and be sure to
follow all label warnings and directions. Incorrect chemi-
cal usage, and any damage or injury that may result, is not
covered by warranty.
To clean your ice machine you will need to purchase a
"nickel safe" ice maker cleaner. Cleaner can be obtained by
contacting AGA Marvel customer service at 800-223-3900
or are available at most appliance retailers or through the
cleaners website. Several recommended cleaners are
listed below:
• Kirby's Certied ice machine cleaner. 100% nickel safe.
• Nu-Calgon nickel safe ice machine cleaner.
• Franklin Machine Products Nickel safe ice machine
cleaner.
- Clear Ice Machine 1
- Máquina de hielo claro 1
- CONTENTS 2
- Recognize Safety Symbols 3
- Words, and Labels 3
- INSTALLING YOUR APPLIANCE 4
- INSTALLING THE DRAIN PLUMBING 6
- INSTALLING THE WATER SUPPLY 8
- FILLER PANEL KIT (OPTIONAL) 9
- OPERATION OF THE ICE MACHINE 10
- OPERATION OF ICE MACHINE 11
- PRODUCT DIMENSIONS 12
- USING YOUR ELECTRONIC CONTROL 14
- CLEANING YOUR ICE MACHINE 16
- Step 1: Removing the Door 18
- Canceling clean mode: 18
- Top of door 20
- Step 6: Secure the cabinet 21
- Step 5: Install the door 21
- OBTAINING SERVICE 23
- 2 hours. Initial start up 24
- Plumbing Problems 25
- Ice Quality 25
- Clean the Ice Machine 26
- Electrocution Hazard 26
- Pump Applications 27
- To Restart the Ice Machine 28
- HOUSEHOLD PRODUCT WARRANTY 31
- 1260 E. VanDeinse St 32
- Greenville MI 48838 32
- 800.223.3900 32
- Pour l’enregistrement : 34
- Bienvenue 34
- DÉBALLAGE DE VOTRE APPAREIL 35
- Grille frontale 36
- Raccordement électrique 37
- Plomberie de drainage 38
- Figure 10 39
- Alimentation en eau 40
- Kit de panneau de remplissage 41
- Figure 13 42
- Figure 15 42
- Figure 14 42
- Production de glaçons 43
- Sonorités nouvelles 43
- DIMENSIONS DU PRODUIT 44
- OFF CLEAN 46
- Verrouillage des commandes : 47
- Rappel pour nettoyage : 47
- Codes d’erreur : 47
- Menu d’options : 48
- Mode Normal et ECO : 48
- Mode de nettoyage : 48
- Étape 1 : Dépose de la porte 50
- Haut de porte 52
- Étape 6 : Fixez l’armoire 53
- Étape 5 : Installez la porte 53
- OBTENTION DE SERVICE 55
- Risque d’électrocution 56
- Qualité médiocre des glaçons 57
- Problèmes de plomberie 57
- Figure 40 59
- Figure 39 59
- Figure 39a 59
- Figure 42 61
- Figure 43 61
- Figure 44 62
- Phone: 800.223.3900 63
- Figura 1 66
- Reconozca los símbolos 67
- INSTALACIÓN DE SU ARTEFACTO 68
- Peligro de choque eléctrico 70
- Manguera de drenaje 70
- Bomba de drenaje opcional 71
- SUMINISTRO DE AGUA 72
- ⁄8" 73
- (45,4 cm) 73
- Figura 12 73
- Figura 13 74
- Figura 15 74
- Figura 14 74
- Producción de hielo 75
- Sonidos nuevos 75
- DIMENSIONES DEL PRODUCTO 76
- USO DE SU CONTROL ELECTRÓNICO 78
- Menú de opciones 80
- Normal y modo ECO (Economía): 80
- Modo de limpieza: 80
- Paso 1: desmonte la puerta 82
- Parte superior 84
- Paso 6: asegure el gabinete 85
- Paso 5: instale la puerta 85
- SOLICITUD DE SERVICIO TÉCNICO 87
- Calidad del hielo 89
- Peligro de electrocución 90
- Figura 39 91
- Figura 39a 91
- Figura 40 91
- Figura 41 92
- Figura 42 93
- Figura 43 93
- Figura 44 94
Relacionado con productos y manuales para Máquinas productoras de hielo Marvel ML15CLP2LP
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales